G S Jha's Page

G S Jha commented on RUD Chains Ltd's photo

CIMG5309

"Pink colour looks good and eye catching.This colour may be standardised globally.Is it so ?"

Aug 19, 2012

G S Jha commented on Susan Straley's blog post 11 Ideas for Clamping in Weld Fixture Design

"Hello Susan, Thanks for your advice and encouragement."

Aug 1, 2012

G S Jha replied to MAHESH CHAND's discussion Knowledge Based Engineering in the group Custom Machine Design

"There is a need of Edge Grinding operation on spring leaves ends.The dimension is 8mm length and 2 mm deep.This requires to avoid digging to the next upper leaf to eliminate spring failure.A m/c needs to be designed for its uniform grinding as the…"

Jul 28, 2012

G S Jha joined Marshall Matheson's group

Custom Machine Design

Standard equipment is the quickest way to make a product. When no suitable equipment is available, custom designed equipment is next to be considered. Engineers with a roadblock in their design can discuss with others with this group.

Jul 28, 2012

23 Comments 6 Likes

G S Jha commented on Susan Straley's blog post 3 Tips for Reducing Errors in Machine Design Revisions

"Revision of any M/c. design is a very sensitive activity.There is no doubt of keeping the original design intact but also it is necessary to keep the plenty of DATA which will make enable to revise the design.The data may be of product produced,tool…"

Jul 27, 2012

G S Jha commented on Susan Straley's blog post 11 Ideas for Clamping in Weld Fixture Design

"We are facing problems in M S Sheets welding of size 2m x 3m.It is getting destorted after welding to the structure.Is there any preventive measure for the same ?"

Jul 27, 2012

G S Jha replied to Jack Daniels's discussion Product Development Projects: First We Look at the Purse

"Development of any product needs prelim analysis of the product.The prime factor is of their uses.Based on this,the product is manufactured and the processes are decided.It has got the impact on the Purse.For ex. where simple drilling of a…"

May 21, 2012

G S Jha replied to Jack Daniels's discussion Why Some People Think Tooling Should Be Free

"Tooling is an integral part of manufacturing of any product.They are different in nature depending upon the Product and the Processes.It is rightly said Tooling cost is always there in the Quotation,direct or indirect.It has been observed in most of…"

May 21, 2012

G S Jha liked Allison Lewis's blog post Great Innovation is Born Out of Collaboration

Feb 29, 2012

G S Jha commented on Allison Lewis's blog post Is Innovation Everybody’s Business?

"Innovation is the new implemented ideas.This can be generated by any one and on any subject/product/process/system.But for any organisation a separate section or department must be there to implement/motivate the same.There are so many innovative…"

Feb 29, 2012

G S Jha liked Allison Lewis's blog post Is Innovation Everybody’s Business?

Feb 29, 2012

G S Jha liked Alyssa Sittig's blog post How engineering contributes to new product introduction

Jan 26, 2012

G S Jha replied to G S Jha's discussion Process improvement of cambering/Heat Treatment of Leaf spring mfg. in the group Rapid Manufacturing Exchange

"It was tried out but could not succeded as hairline cracks observed on the steel surface.However,we are successful the polymer quenching in Forgings. Reg, G S JHA"

Jan 20, 2012

G S Jha commented on Paul J. Heney's blog post What is your engineering degree worth?

"It is obvious that if somebody takes the degree by spending so much of money,he definetly will need the return thru' highly paid salary.But sometimes it is not happening in the real life.Without having the practical knowledge survival is…"

Jan 16, 2012